Mar 25, · Use a paintbrush to apply stripping agent to the furniture as thickly as possible, working in one direction. Leave the stripper on the furniture for the recommended time. Use a putty knife or a nylon stripping pad to remove a test ctcwd.com Time: 48 hrs. If you’re going to paint (or repaint) a piece of furniture, you probably don’t need to strip it. Wash it with TSP substitute mixed with water. Then, using medium- or fine-grit sandpaper, smooth out any bumps or flaking paint and scuff-sand other areas so the new paint will stick better. This applies to painting over clear finishes as well.
Learning how to strip and refinish furniture can be intimidating. So what keeps people from refinishing down to the bare wood? Trust me, the refjnish result will be rewarding! Had I ever fully refinished a piece of furniture before?
Nope, but I was ready for the challenge. I transformed it back to its original beauty for the next generation to enjoy…and I could not be more thrilled! Before we begin with the step-by-step, I want to show you the transforming power of a fully refinished piece. I completed the footboard first and then stood it next to the untouched headboard.
My favorite is called Citristrip and you can find it at most refinishh home store. Get yourself a brush, a pair of gloves and a couple of how to make a clubpenguin account 2013. I used how to choose the right concealer for dark circles 2 inch stiff scraper and a 2 inch soft grip scraper with a knob.
Brush on a generous amount of Citristrip and within seconds you will start to see the old paint bubble up. Allow the gel to set for at least 30 minutes before you try to remove it with a scraper.
For stubborn paint, you can let the anique sit overnight. Here I am scraping off three layers of paint. It came off quite easy! I found that Citristrip worked best on layers of latex paint, but it can be reapplied for subsequent layers of stubborn oil based paint. Brush on… buddha symbols and what they mean scrape….
Keep going until you get down to the bare wood and discard your strippings as you go. Even after all that atique, there is still going to be some paint residue left on the wood — especially if oil based paint was involved.
The soft grip scraper with a knob comes in handy etrip With one frniture on the knob and one hand on the handle, you can apply greater pressure to the wood and scrape off the last of the residue for a clean bare wood finish. Many pieces of furniture have solid carvings or intricate detail work erfinish the wood.
Old paint gets lodged into antiquue crevasses and will not come out with any amount of scraping. The best way to tackle this is more Citristrip and a heavy duty scrub brush! There sfrip no need to hand pick out the paint — that would take way too long. Let the stripping gel do the hard work for you. Apply the Citristrip generously onto the detail work and scrub, scrub, scrub.
The old paint mixing with the gel will become quite goopy, but trust me, it will work! Wipe it all turniture with a old rag or t-shirt and repeat the process if needed. I only had to do it twice! You could also use a bit antiqie mineral spirits to pick up some of the paint as well by mixing it in with the Citristrip before scrubbing. To get underneath these carved leaves, for example, I am using an awl to chip away any last remnants.
Wipe the wood clean with a cloth. Before staining, we need an even surface on our wood. Sanding will do this and open the pores of our wood for a ready acceptance of stain. With an 80 grit sanding disc, I sanded the entire piece thoroughly with the orbital sander and used the sanding block to get into the edges.
When finished, wipe off any dust particles left on the wood with a cloth. The color we chose was Puritan Pine. Stain can be applied with ajtique piece of an old t-shirt. Either approach is fine. Grab some gloves too! Stain goes before varnish! Apply the stain onto your clean naked wood by dipping the rag into the stain and rubbing gow into the wood along the grain line.
Wipe fkrniture any drips and blend in rdfinish color as best you can. Once the stain is on, you can varnish within hours. Here I am applying the shellac with a cheap paint brush, working left to right on the headboard. Unlike polyurethane varnishes, shellac dries fast so you need to work in long strokes, completing one section before starting another. Stdip the piece to completely dry and if needed, add another coat of varnish for extra protection.
Varnish also seals in the stain and gives sheen to the wood. It reveals the organic beauty of your piece! After reuniting the refinished head and footboard with its original rails, we took a step back to admire. All of the work and time I put in to this refinishing project was totally worth it. Instead of all that mint green, you can see the true character of the wood; the way it was when my grandparents acquired it. Always make sure to test for lead paint using a lead paint test kit.
You can find one here. If lead is found, please research ways to remove the lead paint. Those instructions are not shared above. Your email address will not be published. No content on this site may be reused in any fashion without written permission.
Come sstrip in to my garage! Step 2: Remove Paint from Detail Work Many pieces of furniture have solid carvings or intricate detail work in the wood. Step 3: Furnihure Your Wood Before staining, we need an even surface on our wood. Extra time also allows for mistakes to happen — See 3! Wear goggles while you sand! Even though I was using what does research methodology mean how to strip and refinish antique furniture sander with a dust canister, my head was low enough to the project that small pieces of dust still managed to fly in my face.
I walked around with red, irritated eyes for awhile. Shrip goggles even swim goggles would work! Put away your finished pieces! This was my biggest mistake. After I refinished the footboard, I left it on display next to my headboard work area. When I was scrubbing the Citristrip into the detail work of my headboard, some of it splattered onto my footboard and began to eat away at the finish!
That re-do could have been avoided! I love woodworking. I found it really, really furnjture to an and preserve a sentimental piece of furniture. A shade of stain and top coat creates beautiful results. Working with wood is forgiving too. Leave a Reply Cancel reply Your email address will not be published.
All Rights Reserved.
Navigation Menu: Social Icons
Removing the old finish is the most time-consuming part of refinishing wood furniture. Remove old paint and varnish by sanding or through the use of chemical strippers. Occasionally, heat guns can also be used for stripping and are sometimes helpful with the removal of a stubborn finish. 4.
Last Updated: January 10, References. To create this article, volunteer authors worked to edit and improve it over time. This article has been viewed , times. Learn more Valuable tips on refinishing antique furniture. Tips to refinish like a pro without damaging the integrity or value of the piece. Maintain your investment. Log in Social login does not work in incognito and private browsers.
Also, ensure that you work in a well-ventilated area. The fumes can cause dizziness or death if not used in a properly ventilated space. Also, your local hardware specialist can serve as a great source of information with this project, its steps, and material needed. Determine if washing or stripping the finish is best. Decide whether the old finish should come off or if a thorough cleaning will do. Perhaps a rejuvenating coat of varnish will bring it back to its original luster.
If cleaning an unpainted piece, hand cleaner containing pumice used with a toothbrush to get into crevices works well. After cleaning you will know better what you are working with.
In many instances you can save a lot of work by just refinishing parts of the piece. For example the drawer front, the top of a table or bureau or maybe just the arms and seat of a chair may need some work. After making those repairs, you will have rejuvenated the rest of the piece. Using stripper or paint remover. Always use rubber gloves and a mask when using stripper. Use lots of remover and do not brush back and forth.
Put on a thick layer of stripper with one stroke. The stripper will form a skin, like pudding. Place plastic trash bags or newspaper on top of the stripper to help keep the stripper from drying out. Always position the piece so you are working on a horizontal surface, this also keeps you from doing too much at one time.
Allow the stripper to work. Wait until you can rub down to bare wood with one finger without scraping. That is when you can start to remove the stripper. If the piece has a carving, plan to leave the stripper on those areas longer. Remove the stripper. Periodically peek under the plastic to determine how quickly the stripper is working. You may need to apply additional stripper if it the finish is thick. When the finish is soft, scrape it off with an expired credit card or a putty knife.
Note that a credit card, or plastic tool with similar sharp edge, is less likely to damage the wood. Wash off the stripping solution. When the stripper has softened the finish, scrape off as much as possible, so you can wash down the piece with the appropriate solvent or water. It is very important to read the container to determine appropriate washing liquid.
Scrub with a stiff brush with course wood chips, hamster bedding from the pet store will work just fine! This will clean and dry the piece around spindles and carvings. If the piece you are stripping is veneered, be careful when using water as to not lift the veneer. When refinishing, it is more desirable to make every effort to bring forth the original surface and not produce a new one.
To remove light scratches, which is all you should do, use fine grit sandpaper. As a novice, the finer the sandpaper you use, the longer it will take to make a mistake. To remove any stripper residue and set the wood up to accept a finish, open coat aluminum oxide is good. To sand various shapes and moldings on your piece you can use old felt.
The lower the number, the coarser the paper. Stain the piece. It is best to purchase a leading brand of pigmented wiping stain, which are color fast, direct-to-wood stains formulated to develop and highlight the grain of all wood species. Brush the stain on, leave it for a moment and wipe it dry with a dry rag.
Make sure to use rubber gloves and a mask during the staining process as well. For example, adding mahogany to walnut will give a reddish brown color or ebony to walnut combines for a deep dark brown.
Place all used rags in an approved airtight container. Do not leave them on the bench all bunched up, as spontaneous combustion may cause them to burst into flames!
If you do not have a container, lay the rags out flat to dry, preferably outside. Any rags containing solvents are extremely dangerous. Finish your project. A simple method is to wipe on the finish. There are even wipe on polyurethane finishes for optimal protection. Next, wipe it dry. Wait 24 hours, give the piece a light sanding with sandpaper and apply the finish again.
You can do this as many times as you wish, but three or four coats should suffice. Start out with a gloss finish and the last coat should be a semi gloss. Your piece is now ready for that special spot in your home. Melissa Takacs. Try applying a generous amount of mayonnaise to the affected area and let it set for an hour or so. Wipe it off and clean it with a damp, soapy cloth. The mayo "magically" makes the water stain disappear.
Not sure how it works, but it does - give it a try! Yes No. Not Helpful 9 Helpful Include your email address to get a message when this question is answered. Submit a Tip All tip submissions are carefully reviewed before being published. Related wikiHows How to. How to. Co-authors: 8. Updated: January 10, Categories: Furniture Finishes. In other languages Italiano: Rilucidare i Mobili Antichi. Thanks to all authors for creating a page that has been read , times. Did this article help you?