How to replace a laptop fan hp

how to replace a laptop fan hp

Remove and Replace the Fan for HP Pavilion 15-abXXX Notebook PCs

Removing the fan. Step 1. Find the battery lock latch identified by the lock icon on the bottom of the computer and slide it to the unlock position. Step 2. Find the battery release latch identified by the battery icon and slide the battery release latch to the release position to partially eject. Replacing the system fan. Step 1. Connect the cable for the replacement system fan to the motherboard. Step 2. Replace the system fan by inserting the two lower hooks on the fan (1) into the slots in the computer, and then swinging the top of the fan (2) onto the computer. Step 3.

Click here. Sign out. Select registration option. Email address. Error: Javascript is disabled in this browser. This page requires Javascript. Modify your browser's settings to allow Javascript to execute. See your browser's documentation for specific instructions. HP Customer Support. Select your model. How does HP install software and gather data? Before you begin You need a Phillips-head screwdriver and two non-metallic prying tools.

Turn off the computer. Disconnect the Ethernet or modem cable. Disconnect the power cord. Transfer the computer to a clear, flat, stable work surface over a non-carpeted floor. HP strongly recommends the use of an anti-static wrist strap and a conductive foam pad when working on the computer.

Do not remove a component re;lace its h; packaging until you are ready to install it. To reduce afn chance of ESD damage, work over a non-carpeted floor, use a static dissipative work surface such as a conductive foam padand wear an ESD wrist strap connected to a grounded surface.

Servicing internal components increases the risk how to secure your home computer damaging the computer which might not be covered under warranty. Understand the risk and refer to the product's warranty before attempting to service the computer. Hw overview View the following video before using the steps in this article. These same removal and replacement procedures for the fan apply to all configurations of HP ENVY u x convertible computers.

Removing the fan Follow the steps in this section to remove the fan. Step 1. Remove the three 4 mm P1 Phillips-head screws that how to replace a laptop fan hp the fan to replaec base enclosure. Replacing the fan Use the steps in this section to replace the fan. Replace the three 4 mm P1 Phillips-head screws that secure bow fan to the base enclosure.

Select a location. Europe, Middle East, Africa. Asia Pacific and Oceania. Select a language. How do doctors test for down syndrome during pregnancy Back. Search all support. Search help. Replade for better search results Ensure correct spelling and spacing - Examples: "paper jam" Use product model name: - Examples: laserjet pro p, DeskJet For HP products a product number.

Loading Results. The Virtual Agent is currently unavailable. Please try again shortly. Need help troubleshooting? Just ask. Try asking HP's Virtual Agent. Session timed out. Your session on HP Customer Support has timed out. Please sign back in to continue Sign in. Repkace Content. Step 1 Remove the top cover. Step 2 Ensure the battery cable is disconnected from its connector on the system board. Step 3 Find the fan cable and its connector on the system board and Step 4 Remove the fan cable from the routing channel on the base enclosure.

Step 5 Remove the three 4 mm P1 Phillips-head screws replave secure the fan to the base enclosure. Step 6 Lift the fan off of the alignment pins on the base enclosure and remove. Step 1 Place the hhow onto the alignment pins on the base enclosure. Step 2 Replace the three 4 mm P1 Phillips-head screws that secure the fan to the base enclosure. Step 3 Connect the fan cable ti its connector on the system board.

Step 4 Route the fan cable through the routing channel on the base enclosure. Step 5 Ensure the battery cable is reconnected to its connector on the system board. Step 6 Replace the top cover.

Video overview

Removing the fan. Step 1. Remove the top cover. For instructions to remove the top cover, see the HP support document, Removing and Replacing the Top Cover for HP ENVY Step 2. Ensure the battery cable is disconnected from its connector on the system board. Step 3. Find the fan cable and its. Get a paperclip and bend it out. Stick it in the fan grille so as to hold the blades from spinning. Then blast in the strongest air you can find. A can of air is OK, an air compressor is better. If dust chunks fly out that is a good sign you may be fixing it. After you get the fan blown out do a hard reset.

Click here. Sign out. Select registration option. Email address. Error: Javascript is disabled in this browser. This page requires Javascript. Modify your browser's settings to allow Javascript to execute. See your browser's documentation for specific instructions. HP Customer Support. Select your model. How does HP install software and gather data? This document pertains only to HP Slimline computers with the following computer case:.

Before you begin You need a flathead screwdriver. Turn off the computer, and then disconnect all cables. Disconnect the Ethernet or modem cable before disconnecting the power cord.

Transfer the computer to a clear, flat, stable work surface over a non-carpeted floor. HP strongly recommends the use of an anti-static wrist strap and a conductive foam pad when working on the computer. Do not remove a component from its protective packaging until you are ready to install it. Be careful not to slide skin along any interior metal edge of the computer. To reduce the chance of ESD damage, work over a non-carpeted floor, use a static dissipative work surface such as a conductive foam pad , and wear an ESD wrist strap connected to a grounded surface.

Video overview View the following video before using the steps in this article. Removing the system fan Follow these steps to replace the system fan. Step 1. For this procedure, you remove the system fan shown in the rectangle located directly below the drive cage, not the processor fan to the left shown with the circle and X.

Push in the metal tab 1 above the fan and slide the fan down, tip out the top of the fan 2 , and then lift the fan 3 partway out of the computer.

Write down where it was connected so you have that information when you install the new fan. Clip the tie wrap that bundles the power cables and the system fan cable. Separate the fan cable, and then set the fan aside. Replacing the system fan Step 1.

Replace the system fan by inserting the two lower hooks on the fan 1 into the slots in the computer, and then swinging the top of the fan 2 onto the computer. Slide the system fan up, and then press the system fan until the metal tab locks it in place. Bundle the power cables and the system fan cable with a new tie wrap to secure them. Select a location. Europe, Middle East, Africa.

Asia Pacific and Oceania. Select a language. Confirm Back. Search all support. Search help. Tips for better search results Ensure correct spelling and spacing - Examples: "paper jam" Use product model name: - Examples: laserjet pro p, DeskJet For HP products a product number.

Loading Results. The Virtual Agent is currently unavailable. Please try again shortly. Need help troubleshooting? Just ask. Try asking HP's Virtual Agent. Session timed out. Your session on HP Customer Support has timed out. Please sign back in to continue Sign in. Complementary Content. Step 1 Remove the side panel. Step 2 Remove the front panel. Step 4 Remove the system fan screw. Step 5 Push in the metal tab 1 above the fan and slide the fan down, tip out the top of the fan 2 , and then lift the fan 3 partway out of the computer.

Step 6 Trace the system fan cable 1 from the fan through the cable bundle Step 7 Clip the tie wrap that bundles the power cables and the system fan cable. Step 1 Connect the cable for the replacement system fan to the motherboard. Step 2 Replace the system fan by inserting the two lower hooks on the fan 1 into the slots in the computer, and then swinging the top of the fan 2 onto the computer. Step 3 Slide the system fan up, and then press the system fan until the metal tab locks it in place.

Step 4 Replace the system fan screw. Step 5 Bundle the power cables and the system fan cable with a new tie wrap to secure them. Step 6 Replace the front panel. Step 7 Replace the side panel.

Comments:

30.07.2020 06:53 Nezragore:
Welcome, enjoy

31.07.2020 03:31 Mejar:
Critical Modz it is not avaliable in the play store you dumb.