How to Troubleshoot Hunter Ceiling Fan Remote Controls
Install a Universal Ceiling Fan Remote Control for your Pull-Chain Fan Tools and Equipment. We recommend you enlist the help of a friend to install your Hunter fan control system safely and Installing Your Remote Control. Set the fan speed on high and turn the light on using your fan’s pull. Restore power to the fan and re-install the batteries in the remote control. Press and release the three HIGH (3), MEDIUM (2), and LOW (1) buttons on the remote control at the same time. This step must be completed within 30 seconds. Check your fan is successfully paired by turning the fan and lights on and off with the remote control.
How do I wire a universal remote control for my ceiling fan? I purchased them both at home depot. Additional Comments: I found your information to be very informative. Estimated Time: Depends on personal level experience and ability hunte work with tools.
Materials: Make sure the remote control unit is fully compatible with the ceiling fan you have and the size of the lamps that will be hod in the fixture. Wiring Ceiling Fans. Take the mystery out of ceiling fan wiring. Ceiling Fans are a great way to lower your energy bill and brighten up one of your favorite rooms. I just completed a repair like this. The pink, red, yellow and cobtrol control the fan.
This gave me all 3 speeds and full dimmer control over the light, once I hunrer the instsll for activating the remote I believe it was to hold down the fan speed 1 and 3 buttons for 30 seconds. This made the fan blow down, which is what I need in this installation. There is no directional control on the universal remote, but I understand that reversing the yellow and pink wires imstall make the fan blow upward.
I read in several posts online that you can not use the universal remote with a fan of this type, but I can report that what is a forensic chemist works well for us. The one thing I will mention is that all 3 speeds are slower than they used to be, but I think remot may be because my fan is so large. Hi Russ, Thanks how to avoid tunnel in mobile alabama sharing about your successful ceiling fan remote installation.
All the Best! Thanks for these instructions — worked for the most part. The only problem I had was that the fan blew upwards instead of down when wired as stated.
Hi Paul, To change the direction of the ceiling fan you do not have to make any wiring changes. There should be a switch located just below the fan blades on the side of instlal lower assembly where the light is typically attached. Simply slide the switch into the opposite setting and this will change the direction of the ceiling fan rotation.
Enjoy your ceiling fan, Dave. It cohtrol for 20 minutes and then started to smell as burning electronics. So I had to do what I tried how to install hunter ceiling fan remote control avoid doing. I did reverse engineering and that what I came up with: The yellow wire needs to be connected to remkte and both connected to neutral white.
The red wire is connected through capacitor 5uf v to white wire neutral. As you said -to reverse the motor you need to change places of pink and yellow wires.
The method of reverse engineering is a good idea, however be sure to refer to the wiring controk and instructions that came with the specific remote control unit and the ceiling fan that you have. So Hkw, I am going to use your wiring solution on my and I will use a hunter standard universal remote.
Your solution makes sense. Any problems thus far? Hi Steve, Installing a universal remote control on a ceiling fan is a real convenience, and it provides great control stale relationship what to do. Enjoy your ceiling fan!
You must be logged in to post a comment. Electrical Help. May 19, at pm. Log in to Reply. Paul says:.
October 26, at pm. Dave What is mortise and tenon says:. October 27, at reote. Viktor says:. December 21, at pm. STEVE says:. July 24, at am. Click here to cancel reply. Estimated Time: Depends on personal level experience, ability to work ceiping tools, work with electrical wiring, and the available access to the project area. Important: Modifying existing electrical circuits or installing additional electrical wiring should be done according to local and National Electrical Codes, with a permit and be inspected.
Recent Testimonials I think your site offers the the clearest and best electrical information for homeowners I have ever seen on the net. You have given me confidence to do my own projects which I never had before.
Paul, from Foxboro, Massachusetts I wish I found this site earlier, it is by far the best electrical related resource I have found on the web. George, from Scranton, Pennsylvania I love this site for an office worker that does not know anything about electric wiring. Collin, from Grand Rapids, Michigan Thank you for answering my question. I was able to get this done.
This site is perfect. Fsn am glad I found it. Please keep it going. Electrical Tips Newsletter. Ceiling Fan Wiring and Connections. Troubleshooting Light Switch Wiring.
Wiring a Ceiling Fan and Remote Control Module
Feb 27, · Follow this easy guide for how to install your Hunter ceiling fan with light, with remote, and without the light. Getting started ()Installing the bracke. Fan style and remote style may vary. Installing One Fan Operating on Multiple Remote Controls (Handheld or Wall Control) Fan style and remote style may vary. If you want to install one fan operating on multiple remote controls, simply follow the instructions in your Owner’s Manuals, including the remote control pairing instructions. How to Program Hunter Ceiling Fans Go to your circuit breaker or fuse box, and turn off the power to the fan you will be programming. Turn the fan's remote control over, and remove the battery compartment cover. Match the DIP switches inside the remote's battery compartment with the DIP switches on the fan's receiver unit.
In terms of troubleshooting Hunter ceiling fan remote controls, much of the troubleshooting will be similar to troubleshooting other fans:. Another common issue related to dip switches, is the fan turning on or off by itself.
This can be caused by a neighbor, or a roommate having a remote with the same dip switch settings as you by accident. To rectify this, you need to change the dip switches. In any case, make sure the remote dip switches always are positioned the same as the dip switches inside of the fan. I know, we mentioned this earlier — but something you need to check.
One way to tell the batteries are getting low, is if the remote will only work when close to the fan. Keep in mind the signal will not go through walls, so you should be in the same room. While looking inside of the canopy, see if there is any frayed wires, corroded wires, or etc.
See if the receiver, or any other parts appear damaged or even melted. Did the above help you to troubleshoot your Hunter ceiling fan remote? Or, if the troubleshooting worked out, feel free to let us know about that as well. You can also post on our Facebook page as well! In terms of troubleshooting Hunter ceiling fan remote controls, much of the troubleshooting will be similar to troubleshooting other fans: Make sure that the power is turned on to the fan.
This may seem like a rudimentary or obvious thing, and yes we do start at the obvious before we move onto the not so obvious. Try using the remote to turn on the fan.
If you cannot get the fan to turn on at all using the remote, pull on the pull chain and set the fan to the highest speed.
Similarly, try to turn on the light by using the remote. If no luck, turn on the light by pulling the light pull chain. Open the battery compartment on the back of the remote control.
Inside here are dip switches. Check the remote and compare the dip switch settings to the ones inside of the fan. The dip switch settings on the remote and the ones inside of the fan must be the same, or there will be problems with the fan not communicating with the remote properly.
This picture shows where the dipswitches are located on a fan remote, and what they look like. Once troubleshooting is completed, turn the wall switch back on for five seconds.
Turn the remote back on and try again.