How to attach pedals to pedal board

how to attach pedals to pedal board

Securing Pedals to Your Pedalboard

Sep 22,  · It involves using bike chain links to fasten the pedal to the board. This method has a lot more involved with setup, requiring the bike chain links, a drill, screwdriver, screws, and the installation on the pedal. The downside of this method is that swapping pedals is not quick and easy. Basically in a nutshell here are the steps to install them on your pedals. Remove the screws from the back-plate of your pedal. Put one end of the bike chain link over the hole. Re-insert the screw and tighten down. Then use a screw to screw it into the wood top of your pedalboard.

The oriental cockroach how to get rid of idea and design originated in from George de Mestral. His theory was to use hoq same premise and make it useful in everyday situations, one major way was to attempt to replace the need for zippers on clothing. He created a hook side that was rigid and not very flexible, and the opposite loop side that was very flexible to allow them to bend and mold to fit as many hooks to the loops that they could, creating a more secure hold.

The trick was finding the right combination that would be secure, yet easy to remove when pulled with enough force. Instead of the traditional hook and loop method, Dual Lock uses a mushroom shape that sticks to itself to create a tighter, more secure fit. The adhesive has been improved over the years to make it excessively adherent to smooth surfaces. This guy pddals a pretty good job explaining it:. The particular brand that I use is Godlyke Power-Grip pedalboard tape.

This brand uses a similar mechanism to the Dual Lock and also comes in a roll. The thing that I suggest the prdals personally is not to run the hook and loop strips along the center of the pedal. This will make the pedal much more unstable and prone to rocking. With the above mentioned alternatives, an inch or so on the top and the bottom of the baseplate of the pedal will secure them without any rocking or instability.

Another bonus of these two options is the ease of theft on pedals is reduced. Another method is using zip-ties also called cable-ties to secure the pedal to the board. This works really well because the pedal can be put on as securely as you want it to with reduced rocking or wobbling.

To swap a pedal out, just snip the tie and swap the pedal and tie down the new one. One concern is making sure that the connection is secure without rubbing off the paint from the pedal. This method may be difficult for some boards, but there are also brands that are dedicated to making boards with holes designed to be used how to place certified mail sticker on envelope zip-ties.

In terms of theft, the person would have to be able to cut the zip-ties to remove the pedal, which will take a little more time. It involves using bike chain links to fasten the pedal to the board. This method has a lot more involved with setup, requiring the bike chain links, a drill, screwdriver, screws, and the installation on the pedal. The downside of this method is that swapping pedals is not quick and easy.

If you keep the same pedals on consistently, then it would be an excellent option. This method helps a lot in terms of preventing theft too. I will provide a link below to the instructions for those interested. The key thing to remember is that different methods will work for different people. Boad is just a glimpse at attsch few different options that are hod to make your life a little easier hopefully.

Your email address will not be published. Save my name, email, and website in this browser for the next time I comment. Submit a Comment Cancel reply Your email address will not be published. Recent Posts How to break your Ratsbane We need more guitar heroes!

Worship Guitar Magazine

Jan 13,  · Do you just cut whatever size strips, stick it on the back of your pedal, then press it against the fuzzy side on your board? You’ll find pretty quickly that there will be almost zero grip that way. Try this instead – press, then twist one direction, then twist the other direction. Jul 20,  · It is a lot more complicated, but you can remove the bottom plate from the pedal, put it on the board where you want it and then mark/drill through holes in the bottom plate. You will need to get longer screws with the same thread pattern, (5/8" longer etc. depending on what material you used for your board) then screw up through the board, through the bottom plate and into your pedal. Oct 27,  · I use velcro, take the little screws at the bottom of the pedal, make little holes on the velcro that fit the screws and put back the screws with the velcro in between the rubber part, this way I don't even need glue. Done that too, works good also.

So you bought yourself a pedalboard , you're setting it up and all is well with the world. You have all of your effects pedals ordered properly , all your wires have been routed, you've got it all figured out and now it's time to commit. I see this question all over the guitar and pedal forums and everyone seems to have their own opinion on what is best and why it's best. In the end, it really doesn't matter which side it goes on , it's your stuff, you can do whatever you please with it.

As long as your pedals aren't falling off the board then it's purpose has been served. But with that said, today I'm gonna take a stand and say it's time we choose a standard and stick with it! Personally, I think that the hook side of the velcro should go to the pedal, and keep the loop side of the fastener fuzzy side reserved for the pedalboard.

It just makes sense. Though I'm guilty of doing both, I do have my reasons as to why I keep the loop side on the board. Not to mention, we as pedal whores should not have to peel and strip the fuzzy looped side of the velcro off the pedal we just bought on Craigslist damn it. Let's be mindful of other like-minded pedal hoarding individuals, and be aware that someday you could possibly fall out of love with your pedal.

Feelings, tastes, and preferences change over time, it just happens. And when they do you're probably going to want to trade up or sell your pedal on the quest for that ideal tone.

If we as a collective are all on the same page, and all agree that the hook side belongs on the pedal so that when that new person buys your pedal and realizes; hey, one less thing to worry about I know I'm not alone on this, but no one has said anything and left it to subjectivity deciding what side goes where. So instead of bitching, why not be a part of the solution, I'm going to start the revolution here folks.

No, there are plenty of other viable options to mount pedals to your pedalboard. While some are more effective than others, it comes down to who you are as a player and what you plan to do with your pedals. Do you plan to rotate in and out based on the need?

If so Velcro is going to be the way to go. However, if you're the type that is set in their ways and doesn't plan on changing your configuration any time soon, then some of the more permanent options below may be worth looking at. Pedalboard systems like the Holeyboard by Chemistry Design Werks take a different approach from the rails based pedalboard system and have holes allowing you to use zip ties, or hell This is a great option for both static and dynamic setups.

Check out The Holyboard user reviews and price on Amazon. Not sure who originally came up with this idea, but I've seen this idea circulated around the forums and someone finally made a career out of it. This idea is actually pretty slick, essentially what they did was take the link out of a bike chain, and converted it into a pedal mount.

Generally speaking , most effects pedals have a housing screw on the underside of each corner of the pedal. Simply turn the effects pedal upside down and remove the screws. Then, utilizing the existing hardware, thread the screw through either of the eyelets of a Pedal-link.

Re-fasten the hardware screw back into the underside of the pedal. Then mount the other side of the link to the board. Check out Pedal Links user reviews and price on Amazon. This system will fix your pedals in a quick and easy way, allowing you to place and remove them as many times as necessary with only a screwdriver gesture.

Made of plastic, they have been specially designed to adapt the vast majority of pedals in the market, easing any kind of setup. Well, there's my rant about velcro. Do you agree or disagree? Let me know in the comments below. Or if you have a way to secure your effects pedals that I didn't cover tell us about it.

We're all here to learn as we go. Also the pattern of interlocking ovals does not accumulate lint and the connection is much stronger than regular velcro. I have two boards, one large with my entire pedal chain, and a small one for smaller and acoustic gigs. The smaller board has just a compressor, tuner and reverb pedals….

So, easier to move from board to board if I use Velcro over dual-lock … comments, anyone? Notify me of follow-up comments by email. Notify me of new posts by email. This site uses Akismet to reduce spam. Learn how your comment data is processed. Like this? Give it a share Like this: Related Articles.

Then the burning controversial question hits you. Which side of the velcro do I use on the pedalboard? Why do I suggest this? Aesthetics - The hook side of the velcro likes to grab a hold of everything and make it blatantly visible on the top of your board, I tend to like my setup looking neat and generally badass, and granted, to some that may not be a concern, but in my thinking, if you're willing to drop a couple hundred bucks on a pedal you're gonna want to show it off!

So why not give it a decent presentation. That is, of course, unless you enjoy displaying animal fur, carpet fuzz, dryer lint, a few strangers stray hairs, you get my drift.

Structural Integrity -When it comes to the loop side of the adhesive, you can run over that stuff with a steamroller and it will still function as long as the hooks aren't damaged or mangled. But in the case of hook side on the pedalboard , it's wide open to being stomped on, stepped on, scuffed, having things dropped on it, as well as the dirt and grime listed above that make adhesion difficult once it gets to a certain level.

Customization - Keeping the loop side dedicated to the board allows for greater flexibility, say you find a pretty sweet section of shag carpet you want to plaster all over your board. Consistency - A good majority of the pedals I have bought or traded have the hook side on the pedal. But every now and then Who's with me? Here are a few of the alternatives to Velcro: Zip Ties Pedal Links Proprietary Mounting Kits Liquid Nails although highly discouraged, actually, you know what, just forget you read this one Zip Ties Pedalboard systems like the Holeyboard by Chemistry Design Werks take a different approach from the rails based pedalboard system and have holes allowing you to use zip ties, or hell This solution is great for pedalboards that you don't plan to change anytime in the near future.

What do you think? Like this: Like Loading Related Articles.

Comments:

There are no comments on this entry....